1piece 3D Printer 500℃ Thermistor T-D500 M3x15mm Cylindrical High Temperature Sensor 500℃ K500 Thermocouple Sensor Compatible with Volcano V6 Hotend PEI PEEK Nylon Carbon Fiber Printing
Description
🔥 Elevate Your 3D Printing Game!
- ROBUST DESIGN - Crafted from stainless steel for durability and reliability.
- EXTENDED REACH - Comes with a 1-meter cable for flexible installation.
- LIGHTWEIGHT EFFICIENCY - Weighs only 6g, ensuring minimal impact on your 3D printing setup.
- UNIVERSAL COMPATIBILITY - Seamlessly integrates with PT100 V6 hotend and Prusa i3 printers.
- PRECISION TEMPERATURE CONTROL - Achieve flawless prints with a max temperature of 500℃.
The T-D500 Thermistor is a high-performance temperature sensor designed for 3D printing enthusiasts. With a maximum temperature rating of 500℃, it is compatible with various hotend setups, including the PT100 V6 and Prusa i3 printers. Its cylindrical design and lightweight construction make it an ideal choice for precision printing with materials like PEI, PEEK, and carbon fiber.
Specifications
| Manufacturer | POLISI3D |
| Part number | T-d500 |
| Item Weight | 6 g |
| Package Dimensions | 11.7 x 7.9 x 0.3 cm; 6 g |
| Item model number | T-d500 |
| Colour | Silver, White |
| Material | stainless steel,cable |
| Batteries included? | No |
| Batteries Required? | No |
Reviews
K**N
Perfect!
Works as it should with my volcano above 285 degrees. Good accuracy too. At ambient my bed probe and this one shows the same temperature.
S**T
Does not provide correct readings no matter what Marlin firmware settings are used
I expected having to change my Marlin firmware to use setting 66 however this did not work as readings shown on printer were 80 degrees higher than actual hot end temperature. I tried setting 1000 with various resistances but the temperature was consistently lower by around 100 degrees. I even created a custom temperature table using a Excel spreadsheet I found online but after endless twiddling could not get the thermistor to give a reading anywhere near to the temperature at the hot end. I'm going to return the thermistor as not fit for purpose and would recommend others NOT to bother buying it.
J**4
Works great at temp but not great accuracy cold
I performed the changes in the description and it all works great! At low temps, however, it is not very accurate. My stock bed thermistor reads about 26 on average and this one is real jittery usually reading around 35 at room temp, but as soon as it gets hot (about 70+) it smooths out and works great. This is probably why it says to adjust the check time to 30 sec for temp reporting.
S**N
Nie wieder 0 Sterne
Habe es bei mir versucht wie beschrieben und ging leider nicht.Beim Verkäufer habe ich mich gewendet gewendet und kam bis Datum keine Antwort.Schade
A**A
Eccellente
Finalmente un sensore dove non devi litigare per farlo funzionare decentemente... lo sto testando intorno ai 320° ed è davvero ottimo...
A**R
Works with my Dragon fly Hot End- Ender 3 V2
The wire leads are too small to join right up with the main board. I installed this on the Ender 3 V2 with the jyers/marlin firmware. Follow the directions in the other reviews and in the description of the temp sensor on the amazon ad to select the right temp setting in your firmware. Temps bounce a little around room temp, but theyre stable at high temps. Ive had mine up to 320 and it didnt seem to cause issues.
B**!
Durato 1 stampa
Sembrano di buona fattura tuttavia a me personalmente è durato 1 stampa per poi morire miseramente. Non penso userò l'altro...soldi buttati.
Common Questions
Trustpilot
1 month ago
3 weeks ago
