USX Mount Full Motion TV Wall Mount for Most 42-86 inch Flat Screen/LED/4K, TV Mount Bracket Dual Swivel Articulating Tilt 6 Arms, Fits 8” 12” 16" Wood Studs,Max VESA 600x400mm, Holds up to 132lbs

Sturdy and holds a 70 Vizio TV well. We did not need it adherent to the wall like some people do, instead wanted the ability to pull it away for the wall in various configurations for viewing.While it says full movement do realize that once the height is established the arm does not allow any vertical adjustment. Instead you have to drill new holes in the wall at a different height.Therefore height calculation is the most important measurement and you need to understand where you want the top and bottom of the TV to be positioned and then measure relative to where the rack will attach to the wall which is lower than the perimeter of the TV.We wanted the bottom to be about 10" up from the furniture piece where our center speaker and AVR receiver are located. We added another 3" of space that we will need to the future if we get an 86" TV as it will be larger and hang down 3" lower when using the same mount position on the wall.The bolts are substantial and required several drill bits to make the holes into 2x4's, building successively from smaller diameter to larger.If you have a large TV it takes 2 people to assemble. So study the parts and partially assembled them a bit ajread of the instructional which are so-so because you will have to predict some height measurements vis a vis where the mount arm actually attaches to the back of the TV part of the rack. Tape measure!We will collate the visible hanging wires into a black stereo wire sheath.Very good value for the price and ability to hold a lot of weight.Be careful about the mm distances at the back of your TV for screwing in the mount because a range of values is listed but the 400mm is the maximum height and the 600mm refers to the width. Ours is 400x400.

When I ordered my 65" flat screen TV, I knew that I would need a substantial support to mount in on the wall of my home theater. This USX Mount Full Motion TV Wall Mount appeared to be up to the job of supporting my TV's 52 pounds, so I ordered it at the same time. The mount and the TV arrived on the same day.Anything representing that much weight must, of course, be mounted directly on wall studs and not just on wall board. If the wall is masonry, then masonry anchors must be used. Fortunately I had a stud-finder that I had acquired from Amazon several years ago. It located the appropriate wall studs. After taking careful measurements and using the supplied template, I drilled pilot holes through the wallboard and into the studs and used the four included metric lag bolts to secure the base of this wall mount solidly into the studs with my powerful impact tool.All screws required for assembly were included in plastic enclosures including some extras. The brackets that mounted on the back of my TV aligned perfectly with the screw holes that were on the TV. Once the two parts of this mount were properly attached. my wife and I lifted the TV and used the hook brackets to easily secure the TV over the two parallel horizontal bars. Once that was done all of the TV's weight was on the bracket. Flipping up a couple of hinged brackets and tightening the included screws, ensured that the TV could not be accidentally jarred loose from the mount.The entire mount installation turned out to be far less of a hassle than we anticipated. The articulating hinges on the mount enable me to smoothly swing the TV away from the wall to almost any angle to easily gain access to the connections, then press the TV toward the wall for an amazingly flush mount. Another adjustment allows tilting the screen downward if I had mounted the TV high on the wall to make it less accessible.If you are looking for a hassle-free wall mount for a large, heavy TV up to its stated weight capacity, I believe this USX Mount Full Motion TV Wall Mount will do the job for you if you carefully follow its clear instructions.

This kit has it all comes with the tv screws and multiple sizes also you can have the tv flat or you can pull it out and tilt it left and right its a great tv wall mount for the price you can't beat it I would purchase this mount again its real sturdy and has good tilt angles.

I love this TV mount! It was easy to assemble, and easy to use! The quality and materials are great quality, and the price was worth it! The fact that I can move my Tv to any angle I want so that it is easy to attach cords and devices is the best part! It is versatile because it works with every place in the living room to watch TV and flexible in that I can move my TV to meet my watching needs and plug in my game consoles. I would highly recommend!

Study, but the lean forward/backward bit is always just loose enough that my TV starts leaning forwards after a week or so. I have a TV that is on the heavier side but still within the advertised range. The rest of it is great quality though.

One problem I had with my previous mount for my 70” TV was seeing & reaching the HDMI inputs. This mount allows even very large TVs to be extended from the wall to easily reach them and arrange all my cords.I just upgraded to a 75” TV and purchased this well-made mount. Installation was straightforward using the supplied template. And you can make adjustments horizontally, forward/reward tilt, and left/right angle. This allowed me to mount to the studs even though they were not centered to my fireplace mantel. Highly recommend!

This thing is awesome. I was worried it wouldn't hold out 70 lb TV, but it's doing great. The install wasn't difficult, but if you have a 75 inch TV or bigger, you're going to need 3 ppl total. Two to hold ithe tv while one person screws the clasp and tightens the positioning screws. The swivel action is great for sun glare sneaking through the window.